And as usual a big thanks to the beta testers and translators!
Enjoy!
7 Likes
Thanks, Harry
2 Likes
@spockfish What is it?
āUpdate 2026.04.0 [3482] downloaded and available for your device!ā
There has been a hotfix out for Pi 5āsā¦ thatās what youāre now seeing.
1 Like
Hi Harry,
since the update on the USBridge Signature, my DAC(Gustard X18) is not visible anymore in the audio section, and of course no sound, despite several reboots and cable checks.
b5348a013c9b59fe (hoping youāll see something)
I have just run the update on my USBridge Sig and it didnāt finish, all I get is a continuous flashing orange light. Iām going to have to pull the power and hope that I donāt have to do a full reinstall.
Edit: It did reboot properly after I powered it up again.
FYI Harry, for the last two updates on the USBridge Sig I have had to pull the power and re-boot the unit before Ropieee would run.
Hi,
After some reflashing and testing with last 2025 version, it appears my USBridge is having a hardware issue, where the Clean USB port seems KO, so you can stop investigating.
Iāll replace it by a Ustar C19 with a CM4 module
I donāt remember that āAuto updateā features was active in previous, stable version?
Right now this features is inactive for me.
Regards,
Bruno
It has been there āforeverā. Auto update requires a reboot schedule, which on your unit is disabled.
1 Like
Iām sorry Harry, maybe this is my covid fog 
Of course I should turn Reboot schedule on by set daily/weeklyā¦ option.
Regards
Since updating, my devices wonāt connect to it via Airplay. I reboot, I click on ropieee [RoPieeeXL], it connects/disconnects instantly, then when I try again I assume it times out. It then times out every time until I reboot it again. It would happen once in a while before but I havenāt gotten it to work at all since the update.
Hi Harry have one of my units refuses to updateā¦See any issues?
bc41974f859b5a7e @spockfish
Going to order a new SD card soon too just in case
Heej!
Your unit has actually downloaded an update (2026.03). So I would expect that it would show you that an update is available. It already downloaded this release before the release of 2026.04, so hence this is a 2-step.
Are you saying that you donāt see an update notification in the web interface?
Thanks
Doing the update as I have been doing it trying to do each time it comes up results in another update ( I just did one prior to this feedback) so itās not installing. And I canāt determine why. Never seems to install. Iām in an update loop 
Okā¦ found it: the update streaming to disk times out ( at 98% 
)
Iām not entirely sure why ā¦ because the time limit is rather on the safe side.
Unfortunately that means that you need to reflash. Iām gonna increase the time limit a bitā¦
Maybe the image is getting bigger now and the transfer time is not quite enoughā¦ could it be propagation delays due to geographic location?
Iām giving it one more try now then Iāll reflash to a new sd card thatās coming in the mail soon
No, because this isnāt about the download. If you click on āINSTALLā the update has already been downloaded to your RoPieee. This is about the time it takes to actually write the update to disk.
1 Like
Itās a rather old 8gb sd card so maybe time to ditch it
Yeah, could very well be the case. And what I said: corner case. It was at 98%
Hi,
Several years ago my USBridge Sig clean port failed too, an electronic shop, found the issue and import the damage component. In my country labor is not expensive (parts are). At the end I have it running as brand new, I even replaced CM3 with CM4S Lite, put Ropieee on it and is working even better.
Regards