Volume leveling again

Hey Bill, can you share a screenshot of your signal path and audio settings and DSP settings and zone settings in Roon?

I’ve setup my dad’s Roon system with his Sansui AU series integrated (no remote control for this 40 year old integrated) - he likes to jump between albums and doesn’t like having to get up from his chair to adjust the volume on the integrated so Roon’s volume levelling is a lifesaver for him. And it sounds brilliantly transparent, compared with volume levelling turned off.

Something isn’t working correctly and I’m sure the root cause can be found, if you can share more info.

Cheers!

Thanks Sean, here are the screen shots.

![12 AM|348x500]

Actually Roon says there that there can be a compromise with volume levelling and PCM. I am trying to figure out why so many others can’t hear it and why I can’t take for more then a few songs.

Please note I am talking strictly about Volume levelling with no other DSP options turned on.

Yip, my previous post was in reply to Chris’, not your observations re volume leveling.

I too have had to revert to not using volume levelling. Had it on when I used my Pi endpoint but now I have the Naim Atom it really reduces the whole dynamics and takes the life out of it.

hi,

It is interesting that I am also using ropieee and the digione…I also assume the worst case scenario(as described in the Roon's 64 bit floating point volume leveling post) applies as the coax output from the digione to my Chord mojo is at 24bit.

I would need to do some further listening:

  • 16 bit PCM should be fine with volume leveling
  • 24 bit PCM might have the issue
  • DSD should be fine with leveling on/off

I really like the convenience of volume leveling though, and figuring this out would be great!

Hey Bill, can you also screenshot the 1st 2 tabs of the Audio settings page.

Cheers!

Thanks Sean for your help!

Do you means these tabs:

Wouter, my DAC is an early Sabre 32 bit Dac and limited to 24/192 input. I haven’t replaced it because its designed so nicely and it’s transparency is so high. Most DAC’s are too “heavy sounding” for me. This DAC has been criticized for been too “light”. The USB input is not the best and so the DIGIONE has breathed new life into it.

I tried upsampling in Roon to 24/192 with all the filters and it smoothed things out a bit too much for me. Not a huge difference but our reference songs that are very “emotional”, you know that ones that move you, seemed seemed to be less involving. I don’t know what my Sabre Dac is doing but whatever it is, I love it.

We working at home allot now, and so I have music on all day and volume levelling would be nice.

But, I am starting to think that the problem is more with how resolving or dynamic ones amp/speaker combo is. That might explain why some can hear the difference and others can’t. And just to be clear, this has nothing to do with component cost. I have very efficient moderately price gear, but it is all from boutique manufactures built around very high efficiency speakers. Any little change I can hear.

Sorry, I replied to Simon instead of you!

Thanks again for you help!

Do you means these tabs:

Hey Bill, yes thanks for tall the tabs. Nothing jumps out at me from all those screenshots that can explain the night and day difference you’re hearing. I think you may need to tag support for help on this.

What DAC, and amp and speakers, if you don’t mind me asking?

I didn’t see any mention of LUFS so just in case. That is fully adjustable. I notice on your zone it is the default -23LUFS (Target Volume Level). Depending on your library and tastes you may benefit from experimenting with that. Some have reported good results at -20LUFS or even -18LUFS.

Decware Torii III with v-caps. Very fast and transparent. Not at all “tubey”. I had it made with 16 ohm transformer taps to drive my 16 ohm Zu Superfly speakers (101 db).

Thanks I will experiment with that. I have not played with that at all.

Thanks Bill. And which DAC?

23LUFS is a relatively new standard to steer the industry from over compression. Roon has settled on that as a default but it may not work for you depending on your tastes and the history of your library.

Sorry! The DAC is an Anedio D2, an early Sabre 9018 but done really well. My friend here has a Lumin S1 with Audio Research REF 6 Pre and GS 150’s into Wilson Sasha’s and my little rig holds its own. :wink:

But, with tube regulation for inputs, outputs and tube rectification; its not really fair fight. :slight_smile:

I think his Lumin S1 costs more then my whole system!

And volume levelling sounds the same on his system as well… So i don’t think it has anything to do with the front end.

You have a nice system indeed. Report back after trying Tony’s tip above, adjusting the default LUFS value.

Thanks Tony. I will try this out.