How to install RoonOS 3.0 on a NUC

Ok, just making sure not missed anything.

Given that

  • The NUC can’t be plugged into a TV, as with the NAS units in a different room
  • I don’t use Tailscale for ARC, the port approach works fine for me
  • I use network connected volumes rather than direct connected USB drives
  • The NAS connections are all working fine into the Roon Server

I don’t see the need to update and move to this RoonOS 3.0 version, unless anyone can see any fundamental difference given the above.

Potentially slightly outdated, whatever was current when the installer was made. But after the first boot, it checks for updates and you can then install any automatically if available. That is mentioned in the linked instructions.

Yep (10char)

My update to 3.0 was less than smooth tbh and I was already on 2.1.

Constant restarts of rock after installation which eventually caused my attached 8 TB HDD to become in a read only state.

Had to remove and run windows drive repair tool.

Reattached to the nuc and exactly the same performance again!!

Third time was a charm though, it restarted just twice and did not affect the HDD this time.

Very disconcerting and I have little confidence that it might not happen again.

No I have not done any further investigation. Rock has been running for 16 hours now so I just need to keep monitoring it

Known issue for some machines apparently, there are several Support threads about it.

Perhaps this

Correct and well aware but…odd that it stopped the restarts after a while with no intervention or other changes on my part.

Of course it may only be a temporary reprieve :confused:

Yep, while out using Arc it crashed again and sent the HDD into read only mode.

Obviously something not quite right.

Successfully rolled back to 2.1 for now until Roon resolve this.

Hi again

Has any of you with a nuc version 7 or 8 and who has installed roon 3.0 had any regrets after installing roon 3.0

Do you think roon 3.0 is better than the old version on a nuc 7 or 8 :slight_smile:

all the best

Frank / Denmaek

The NUC8 (perhaps only some models?) has the issue that RoonOS reboots permanently if nothing is attached by HDMI. (An HDMI dummy plug for a few EUR helps)

My Roon Rock is on a Intel NUC Frost Canyon Tall I7-10710U. I’m on Roon Server version - 2.74 (build 1712) and RoonOS version - 1.0 (build 259) production. I have an extra internal SSD in my NUC with my music library

Please let me know if I have understood the upgrading procedure for getting to ROON 3.0

First I will have to change the NUC’s BIOS to UEFI. This is explained here:

I then have to upgrade (or rather re-install and upgrade) my ROON OS from 1.0 to 3.0. This is explained here:

When I have upgraded (or rather installed 3.0) I should Restore the backup. Explained here:

If this is correct I have the following questions:

  1. Should first upgrade the NUC’s BIOS before changing to UEFI?

  2. Should I remove my SSD with the music library before doing this upgrade? If yes: when should I install it again. At what stage? After the Rock has been installed?

  3. It is not possible to only change the BIOS to UEFI and then do a normal upgrade from 2.74 (build 1712) to 3.0 from within ROON?

Can someone please confirm or correct me if I have understood this incorrect.

best

/klas

Have you had success setting up your NUC? Is it intel based or the newer ASUS?

Mine is an Intel series 10 i7 , I have chickened out for the time being . I ill find a quiet moment as it will entail taking my Roon server down . There is too much going on with Box Sets at the moment to risk it !!

I have no rush to do it I don’t use ARC and hence don’t need Tailscale

If and when Roon decide to pull support on 1.0 I will do it . I only asked in case there was a quick update path.

Gotcha.I got rid of my Grimm MU1 streamer and had to go to a NUC which I completely did on my own with lots of instruction from the team. It took me a while and longer than expected, but it worked.Good luck.

I upgraded my NUC 7i5 to UEFI years ago when the option for UEFI was first introduced.

  1. I didn’t bother.
  2. Absolutely, put it back in AFTER doing a database restore on the new installed 3.0 as the last step.
  3. NO it is not. UEFI changes the boot structure so that the previous Legacy hard drive will need to be reformatted.

Honestly, the easiest way to do this with giving yourself a way to recover, is to buy a new drive to use as the OS drive.

Take out the current OS drive and Storage drive.
Change the boot to UEFI.
Install the brand new drive and load Roon 3.0 directly.
After it is done, restore the database.
And then put the storage drive back in.

If it all works, then you have a spare drive you can repurpose for other things.

Ah that is not a bad idea

This is RoonOS and not Roon Server
So it is the underlying operating system for the NUC that the Roon Server runs on.
The OS and Roon Server application are separate.

None of the functionality in Roon Server is changed or is dependent on the OS being used.
Changing/upgrading RoonOS from 1.0 to 3.0 will have no effect on the running of Roon Server (unless anyone has either found a difference or tells us about one).

So unless you need one of additional capabilities of this RoonOS, namely “Now Playing” on the HDMI output, Tailscale for ARC, later Samba implementations, repair for USB-based DAS, is it worth the upgrade steps?

I suspect sooner rather than later Roon will stop supporting OS 1.0 and we will hav to move but until then “if it ain’t broke” !!

It’s just an OS, the only support burden is monitoring security advisories. As long as there a Linux kernel releases for this old branch (which will be for a very long time), I don’t see why they would alienate customers

That is what I did with my NUC8 i5 BEH. Messing with an ex WIN11 drive and fix all the partitions is possible, but I decided that that is something for a later day when I need the drive as an additional storage